Set Up Technician I - 1st shift
Company: Cambro Manufacturing Company
Location: Huntington Beach
Posted on: January 4, 2022
Set-Up Tech I is responsible for performing the complete mold
change process including mold/supply preparation in advance, mold
removal, mold installation and secondary equipment set-up, clean
up, and organization. Set-up Tech 1 personnel are responsible for
clean-up of machine and surrounding areas, including proper clean
up and storage of all mold change materials and supplies. Basic
Pultrusion mold processing skills required.
ESSENTIAL DUTIES AND RESPONSIBILITIES include the following. Load
and unload raw materials for core production.
Set up, run, adjust, and change dies and equipment.
Ensures that molds are properly prepped in advance.
Ensures that molds being pulled are properly shut down and prepped
for transportation to the mold shop.
Sets up all auxiliary equipment, label and traverse end piece
machine related to each job change.
Set up reels for proper feeding of finished core material.
Effectively perform shift changeovers by preparing and cleaning any
available equipment/supplies to minimize downtime.
Comply with safety and operating policies and procedures regarding
equipment, materials, and finished goods.
Maintain a clean, safe, and orderly work environment.
Communicate with team members to assure complete understanding of
directions, issues, problems, changes, or other challenges.
Recognize and report any problems, issues, discrepancies, or
questions to Manager/Supervisor in a timely fashion.
Measure, weigh, and mix resin materials in conformance with
specifications and procedures.
Set up raw materials for new production runs.
Remove product, machine attachments, and waste material from
Understands all procedures associated with the handling of
hazardous waste and other trash generated by the department.
Monitor reels to ensure core material is wrapping consistently.
Recognize characteristics of resins and epoxies.
Maintain maximum efficiency in the department
Assists as needed in performing start-ups, changes, relieving for
breaks, etc. as assigned by shift supervisor.
Must have reliable and consistent attendance as well as be punctual
and dependable in order to meet the needs of the department and the
Ability to read and interpret safety rules, MSDS (Material Safety
Data Sheets), operating and maintenance instructions, and any
Ability to add, subtract, multiply, and divide all units of
measure, using whole numbers, common fractions, and decimals.
Ability to compute rate, ratio, percent, and draw and interpret bar
Ability to apply common sense understanding to carry out
instructions furnished in written, oral, or diagram form. Ability
to deal with problems involving several concrete variables in
Some basic computer skills are required for documentation and
record keeping of test/run data.
The physical demands described here are representative of those
that must be met by an employee to successfully perform the
essential functions of this job. Reasonable accommodations may be
made to enable individuals with disabilities to perform the
Sitting, walking, standing, bending at the neck, bending at the
waist, squatting, climbing, kneeling, crawling, twisting at the
neck and waist, repetitive use of hands, simple grasping, power
grasping, fine manipulation, pushing and pulling, reaching above
and below the shoulder, carrying/lifting up to 50 lbs.
Driving cars, trucks, forklifts and other equipment
Working around equipment and machinery
Exposure to excessive noise
Exposure to dust, gas, fumes or chemicals
Working at heights
Use of special visual or auditory protective equipment
Steel-toe slip-resistant shoes
Hearing protection (e.g. ear plugs, ear muffs)
QUALIFICATIONS To perform this job successfully, an individual must
be able to perform each essential duty satisfactorily. The
requirements listed below are representative of the knowledge,
skill, and/or ability required. Individual must have basic
knowledge of the Pultrusion Molding process and the Mold Set-Up
process. Individual must also have a basic understanding of the
molds, materials and machinery related to Pultrusion molding
Must be able to read and interpret gauges and record
EDUCATION and/or EXPERIENCE
High school diploma or general education degree (GED); or one to
three years related experience and/or training; or equivalent
combination of education and experience.
OTHER SKILLS and ABILITIES
Previous mechanical/electrical/hydraulics training or experience
CERTIFICATES, LICENSES, REGISTRATIONS
Must have valid class C license for forklift certification
CAMBRO is proud to be an equal opportunity workplace. All qualified
applicants will receive consideration for employment without regard
to and will not be discriminated against based upon race, color,
religion, national origin, gender, sexual orientation, gender
identity, age, physical or mental disability, genetic information,
military or veteran status, or other characteristics protected by
Keywords: Cambro Manufacturing Company, Huntington Beach , Set Up Technician I - 1st shift, Professions , Huntington Beach, California
Didn't find what you're looking for? Search again!